Henkel LOCTITE 411 instant dry glue Metal plastic rubber small gap adhesive gap filler
Loctite 411 enhanced
Loctite adhesive
Instant Dry Glue Series :411 product introduction
Loctite Product 411 is a single component, high viscosity, impact resistant, peel resistant cyanoacrylate adhesive.
Typical use
Can be bonded to most rubber, plastic or metal, suitable for low curing speed, or parts required to withstand shock and vibration.
LOCTITE 411 is a water white to mist high viscosity and cyanoacrylate follow-up gel. This product is a multi-purpose product, gap filling instant adhesive is suitable for bonding rubber, plastic and metal. It demonstrates excellent peel strength with higher heat resistance. This product can be fixed in seconds and can achieve full cure in 24 hours at normal room temperatures.
- 描述
- Global Tab
描述
Product Features
1. Excellent stripping strength
2. Fix it within seconds
3. Excellent additional heat resistance
4. Bond rubber, plastic and metal
Method of Use
1. For all adhesives, the correct surface treatment is a key factor to ensure the bonding effect
2. The surface to be bonded must be clean, dry and free of oil. Clean the substrate surface with LOCTITE SF 7063 or LOCTITE SF 7070 if necessary
3. To speed up fixation, LOCTITE accelerators can be applied on the side of the substrate to be bonded
4. In order to improve the bonding effect of difficult materials (PPPE, PTFE, etc.), substrate LOCTITE 77O can be coated on the surface of the substrate to be bonded
Get free sample or more information , please contact me with my email: jenny@fuji-hk.cn . thank you .
相关产品
-
LOCTITE271 designed for the permanent locking and sealing of threaded fasteners.
LOCTITE
271 designed for the permanent locking and
sealing of threaded fasteners. The product cures when
confined in the absence of air between close fitting metal
surfaces and prevents loosening and leakage from shock and
vibration. Typical applications include the locking and sealing
of large bolts and studs (up to M25 ).Specific Gravity 25 °C 1.1
Flash Point – See SDS
Viscosity, Brookfield – RVT, 25 °C, mPa·s (cP):
Spindle 1, speed 10 rpm, 400 to 600LMS -
LOCTITE 609 designed for the bonding of cylindrical fitting parts
LOCTITE 609 is tested to the lot requirements of Military
Specification Mil-R-46082B. Note: This is a regional approval.
Please contact your local Technical Service Center for more
information and clarification. -
LOCTITE 416 general purpose cyanoacrylate instant adhesive.
The rate of cure will depend on the bondline gap. Thin bond
lines result in high cure speeds, increasing the bond gap will
decrease the rate of cure. -
LOCTITE 638 designed for the bonding of cylindrical fitting parts, particularly where bond gaps can approach 0.25 mm
LOCTITE 638 is designed for the bonding of cylindrical
fitting parts, particularly where bond gaps can approach 0.25
mm and where maximum strength at room temperature is
requiredThe product cures when confined in the absence of air
between close fitting metal surfaces and prevents loosening
and leakage from shock and vibrationTypical applications
include locking bushings and sleeves into housings and on shaftsL -
LOCTITE 420 Quick-drying Adhesive for high and low temperature resistant metal plastics for general purpose
LOCTITE 420 is a clear, colorless, all-purpose adhesive containing ethyl capillarity. Applicable to metals, rubber and plastics, Primer LOCTITE SF 770 or LOCTITE SF 7239 can also be used in combination with polyolefin. The initial fixation time is 5-20 seconds.
Product Features
1. Fast curing between two surfaces
2. Ideal products for bonding small and medium sized parts
3. It has good adhesion to most substrates
4. Suitable for metal, rubber and plastic
5. The initial fixation time is 5-20 seconds
6. Capillarity
7. No solvent
