-
Loctite554 pipe thread sealant
Loctite554 anaerobic type pipe thread sealant, henkel loctite 554 glue product for less than 5.0 cm in diameter threaded fittings and pipeline provides maximum resistance to solvent protection. Recommended products applied to the presence of reinforcement learning material of refrigeration system and the maintenance of refrigeration. Sealant can replace the hardening compounds, lead oxide, glycerol and sealing tape. This product is not suitable for sliding fit pipe joint. The application of the product is usually working temperature is 870 ℃. Typical applications consist of metal and glass factories, chemical processing, paper processing, waste disposal facilities and textile industry.
-
Loctite609 cylindrical solid glue
LOCTITE609_ loctite 609 cylindrical rubber are _ [low viscosity/high strength]
LOCTITE henkel LOCTITE 609 glue, LOCTITE 609 cylindrical solid glue, low viscosity, high strength, suitable for filter, interference fit, hold the key to shaft, bearings, small motor rotor shaft and bushing, cooperate with the strength increase temperature, repair the wear of a shaft with a hole or ultra poor parts. The ideal radial fill the gap of 0.13 mm below, after 24 hours can provide 21 mpa shear strength, can easily switch different parts of the metal materials, can withstand the temperature to 149 degrees.
Typical use: high intensity -
LOCTmtedITE 518 single component, iu anam strengh,es weroant wurhen bic shich cealconfined in the absence of air between close fitting metal surfaces.
LOCTITE 518 provides robust curing
performance. It not only works on active metals (e.g. mild steel)
but also on passive substrates such as aluminum with a low
copper content. The product offers gap performance to 0.25
mm (0.01 in) and contamination tolerance. It cures in the
presence of minor surface contaminations from various oils,
such as cutting, lubrication, anti-corrosion and protection fluids
and cleaners containing surfactants and corrosion inhibitors. -
Original authentic Henkel Loco JM7000 high temperature conductive die silver adhesive conductive adhesive bonding space chip
Subsequent post-mount thermal exposures (e.g., lead bonding and/or higher 370℃ caps) do not generally degrade product performance. JM7000 comes with pre-mixed and frozen 3cc syringes that can be transported on dry ice and should be stored at -40c.
-
Original authentic Henkel LOCTITE4307 High temperature resistance impact UV curing UV adhesive
LOCTITE 4307 is designed for adhesive applications requiring rapid fixation, fillet cure, or surface cure. Uv curing features help to cure exposed surface areas quickly, thereby minimizing frosting and providing an alternative to solvent-based accelerators. Suitable for assembling disposable medical equipment.
-
Original Henkel LOCTITE LOCTITE 2700 Glue bearing motor motor adhesive thread locking anaerobic adhesive
No danger signs, no risk phrases and no safety phrases; “White” material safety data sheet
High strength universal thread locking adhesive provides the best results
Prevents loosening of components caused by vibration, such as pumps, gearboxes or presses
Suitable for all metals, including passive substrates (e.g. stainless steel, aluminum, electroplated surfaces)
It can be decomposed by heating to 300°C.
WRAS certification (BS 6920): 1104508 -
Original Henkel LOCTTIE Loctite 190024 UV curing adhesive liquid optical UV shadow free glue
TYPICAL PROPERTIES OF UNCURED MATERIAL
Specific Gravity @ 25 °C 1.12
Viscosity, Brookfield – HBT, 25 °C, mPa·s (cP):
Spindle TB, speed 10 rpm, , Helipath 18,000 to 35,000LMS
TYPICAL CURING PERFORMANCE
LOCTITE®
DSP 190024™ can be cured by exposure to UV
and/or visible light of sufficient intensity. Surface cure is
enhanced by exposure to UV light in the 220 to 260 nm range.
Cure rate and ultimate depth of cure depend on light intensity,
spectral distribution of the light source, exposure time and light
transmittance of the substrate through which the light must
pass.
Fixture Time
UV fixture time is defined as the light exposure time
required to develop a shear strength of 0.1 N/mm².
UV Fixture Time, Glass microscope slides, seconds:
6 mW/cm², measured @ 365 nm ≤10LMS -
Original LOCTITE 28630 Transparent Quick Drying Glue Low bleaching low viscosity good permeability universal quick drying glue
Loctite 28630 instant dry glue Features:
1. Low albinism
2. Penetration level
Loctite 28630 Instant dry adhesive Application scope:
Widely used in ink cartridge and general industry, low viscosity, good permeability. Suitable for rubber, plastic, electronic industry, metal, toys, all kinds of buttons and other materials bonding.
-
Original LOCTITE LOCTITE 325 structural glue 50ml clear colorless high temperature resistant acrylic adhesive
Loctite 325 structural adhesive Typical application:
Loctite 325 structural adhesive has excellent temperature resistance. The activator Loctite 707 can be used to help solidify between two tightly attached parts. It is mainly used for bonding rigid metal parts to the surface of metal or ceramic materials under the condition of thermal cycling, such as the bonding of motor parts
-
Original LOCTITE511 single component anaerobic glue acrylic pipe thread sealant
Brand: LOCTITE
Model: 511
Specification: 250 ml
Origin: China
Shelf life :12 months
Component: Single component
Properties: Thixotropic, medium and high viscosity applications: bonding metal, ceramic, etc -
Quick dry type locking metal plastic thread locking glue
Loctite425 instant glue, henkel loctite 425 surface curing thread locking agent is a kind of low intensity, fast curing cyanoacrylate adhesive
-
Red oil resistant type high strength screw locking glue
Mixer viscosity (mPa) s) 400 ~ 600;
Largest fill gaps: 0.13 mm;
Heat resistance: – 54 ℃ to 150 ℃;
The average removal torque: 25 ~ 40 n. m.
The average failure moment: 17 ~ 40 n. m.
Cure time: early is 20 minutes, the whole is 24 hours;
Packing specification: 50 ml and 250 ml bottle.
