-
Loctite 515 plane sealant anaerobic flange sealant instead of washer nut plane seal
Application:
Commonly used as in-place washers for pumps, thermostats, compressors, transmissions and safety locks, more suitable for rigid metal flanges, moderate curing speed, thixotropy.
Storage Conditions:
Conditions will be ideal if the product is stored in a cool, dry place in the temperature range of 8-28 ° C (46-82 ° C). To avoid contamination of unused glue, do not pour any glue back into the original package.
-
Loctite 603 cylinder retaining adhesive anaerobic adhesive metal retaining parts high strength thread bearing gear
Brand Name: Henkel Loctite
Product type: General purpose cylindrical adhesive
Product model: Loctite 603
Product specification: 50 ml
Product color: Green
Viscosity: Low viscosity
Strength: High strength
Curing time: 8 minutes for initial setting, 24 hours for full setting
Operating temperature: -55c to +150℃
Suitable material: Suitable for all kinds of metal cylindrical retaining parts
Application scenario: It is suitable for the bonding of cylindrical assembly parts, especially for the metal surfaces that cannot be clean and tightly fitted -
LOCTITE 609 designed for the bonding of cylindrical fitting parts
Cure Speed vs. Substrate
The rate of cure will depend on the substrate used. The graph
below shows the shear strength developed with time on steel
pins and collars compared to different materials and tested
according to ISO 10123. -
LOCTITE 609 designed for the bonding of cylindrical fitting parts
LOCTITE 609 is tested to the lot requirements of Military
Specification Mil-R-46082B. Note: This is a regional approval.
Please contact your local Technical Service Center for more
information and clarification. -
Loctite 635 glue special motor motor glue magnetic steel anaerobic glue cylinder holding adhesive
Brand: LOCTITE
Model: 635
Specification: 250 ml
Strength: High strength
Origin: China
Curing method: anaerobic curing
Curing time: full setting 24 hours
Application: Adhesive metal, fastening with thread -
Loctite 638 cylindrical solid anaerobic adhesive glue
Loctite638 cylindrical solid glue, henkel loctite 638 glue, anaerobic adhesive, is a kind of single component, high strength, high viscosity, anaerobic retaining adhesives, in the case of isolated from the rest of the air, this product in two close coordination between the metal surface of rapidly solidified high strength.
Typical application: used for bonding cylindrical mating parts, especially suitable for bonding gap of approximately 0.381 mm parts and requirements under the condition of room temperature has a great strength. Typical applications include bush and sleeve is fixed to the frame or shaft. -
LOCTITE 638 designed for the bonding of cylindrical fitting parts, particularly where bond gaps can approach 0.25 mm
LOCTITE 638 is designed for the bonding of cylindrical
fitting parts, particularly where bond gaps can approach 0.25
mm and where maximum strength at room temperature is
requiredThe product cures when confined in the absence of air
between close fitting metal surfaces and prevents loosening
and leakage from shock and vibrationTypical applications
include locking bushings and sleeves into housings and on shaftsL -
Loctite 640 anaerobic glue one component high temperature resistant acrylic cylinder holding adhesive
Brand: LOCTITE
Name: cylindrical holding glue
Model: 640
Origin: China
Class: Acrylate
Specification: 50 ml / 250 ml
Component: single component
Curing time: full setting 24 hours
Curing method: anaerobic curing -
Loctite 641 single component cylindrical anaerobic holding glue acrylic adhesive
Brand: LOCTITE
Model: 641
Specification: 50 ml
Origin: China
Shelf life :24 months
Curing method: anaerobic curing
Properties: Medium viscosity, single component
Application: Adhesive cylindrical fittings, etc -
Loctite 648 glue high temperature resistant cylindrical holding adhesive acrylate anaerobic adhesive
Brand: LOCTITE
Model: 648
Specification: 50 ml
Origin: China
Shelf life :24 months
Curing method: anaerobic curing
Properties: Single component, low viscosity
Application: Cylindrical fittings, etc -
Loctite 649 high strength low viscosity anaerobic glue acrylate retention adhesive
Brand: LOCTITE
Model: 649
Specification: 50 ml
Strength: High strength
Origin: China
Curing method: anaerobic curing
Curing time: full setting 24 hours
Application: Bonding metal, filling gap -
Loctite 660 high strength cylindrical holding glue fill gap shaft pin wear repair glue
Notes for Loctite 660 Glue:
1. This product is not suitable for use in pure oxygen and/or oxygen-rich environment, and cannot be used as a sealing material for chlorine gas or other strong oxidizing substances.
2. This product is not recommended for use on plastics (especially thermoplastics, which may cause cracking). It is recommended that the product be tested for material compatibility before application.
3. When using cleaning agent to clean the surface of the material, the compatibility of the cleaning agent and glue should be checked. In some cases, the cleaning agent used may affect the curing and performance of the glue.
Loctite 660 glue for disassembly: Local heating to 250℃ for assembly. Disassembly is performed while heating.
Locate660 glue clarity: The intercom is immersed in solvent or mechanically polished using tools such as a steel brush.
Storage conditions of Loctite 660 Glue: The product is stored in unopened original packaging in a cool and dry place. The storage method is marked on the outer package of the product. The ideal storage condition is: 8℃-21℃.